Home >> News >> News

Product List of Photoinitiators - Haihang industry

Jan. 30, 2019

Haihang industry is a professional photoinitiator manufacturer and has been researching and producing photoinitiators since 2010. Dozens of different photoinitiators are now available. The actual effects produced by different photoinitiators vary widely for different applications. Therefore, different types of photoinitiators will be briefly introduced in this product list.

Below is a list of photoinitiator products for Haihang industry

Irgacure 819 | CAS# 162881-26-7 | C26H27O3P

As a new type of photoinitiator, Irgacure 819 is mainly used in the coatings, inks, adhesives and other industries. They have greater absorption in the ultraviolet and visible regions and can initiate curing more effectively than other photoinitiators for pigmented coating systems. The acylphosphine oxide photoinitiators hardly yellow under curing and long-term light radiation, so they can be used in applications where yellowing is critical, such as white, light inks and coatings. In addition, the acylphosphine oxide has a bleaching effect on the light, and the radiation can penetrate the coating, which is beneficial to the complete curing of the thick film.

Irgacure 651 (Benzil Dimethyl Ketal) | CAS 24650-42-8 | C16H16O3

Irgacure 651, can be used to formulate light-curing adhesive with a maximum absorption wavelength of 337nm. It is suitable for unsaturated polyester/styrene, acrylate, siloxane, and other systems. It has very good thermal stability and high annihilation resistance. And photoinitiator activity, but yellowing is more serious.

Irgacure 907 | CAS 71868-10-5 | C15H21NO2S

Photoinitiator 907 A highly efficient free radical (I) type photoinitiator used primarily for UV polymerization of the corresponding resin. Photoinitiator 907 has a high photoinitiator efficiency with an absorption wavelength of 330 to 385 nm. It is often used in combination with a thioxanthone photoinitiator to enhance light absorption. Used to initiate rapid curing of systems such as acrylates and methyl methacrylate. The photoinitiator 907 can absorb the ultraviolet radiation energy to form a radical or a cation during the curing process of the ink and initiate polymerization, crosslinking and grafting reaction of the monomer and the oligomer, and cure the ink into a short time. A high molecular polymer of a three-dimensional network structure.

The reference dosage is 2%~6%.

Irgacure 184 | CAS 947-19-3 | C13H16O2

Irgacure 184 is one of the most commonly used photoinitiators with high photoinitiation activity, excellent thermal stability, and no yellowing. It has a maximum absorption wavelength of 333 nm and is mainly used to initiate systems such as acrylates and methacrylates. Fast curing.

The reference dosage is 3% to 5%.

Irgacure 307 | CAS 94576-68-8 | C20H23NO2

Irgacure 307 is a new type of photoinitiator that replaces the traditional Type 907 photoinitiator. Due to its biotoxicity in 2011, it is the most cost-effective alternative to Irgacure907.

Irgacure 1173 | CAS 7473-98-5 | C10H12O2

Irgacure 1173 is one of the most widely used non-yellowing photoinitiators with a maximum absorption wavelength of 331 nm. It combines with polyester, acrylate, reactive diluents and the like to form a photocurable adhesive. However, in unsaturated polyester/styrene systems, the photoinitiation efficiency of HMPP is inferior to that of benzoin ether photoinitiators. It can also be used in aqueous UV curing systems. The reference dose is from 1.0% to 5.0%. Irgacure 1173 is not suitable for applications where the odor is more stringent. The reason is that the residual initiator is volatile and the photolysis of the initiator produces traces of benzaldehyde and acetone which can cause excessive odor.

Darocur 2959 (Irgacure 2959) | CAS 106797-53-9 | C12H16O4

Photoinitiator 2959 is an FDA approved a system that allows for the use of photoinitiators. Low odor, low volatility, low yellowing, can be used in adhesives that are not in direct contact with food. Photoinitiator 2959 is a highly efficient non-yellowing UV photoinitiator used to initiate UV polymerization of unsaturated prepolymerization systems, particularly for low odor, waterborne acrylate, and unsaturated polyester resins.

Irgacure 754 | CAS 211510-16-6

Irgacure 754 is a high-efficiency, low-odor free radical (I) photoinitiator with low volatility, low odor and low migration, and the activity is comparable to or slightly lower than 1173. Clear varnish commonly used on wood and plastic surfaces. It can be applied to traditional UV curing formulations, especially in areas requiring low odor, low heat release, and low yellowing.

Irgacure 784 | CAS 125051-32-3

Irgacure 784 has a special photoinitiation mechanism that is ideal for thick and dark curing systems, curing coatings over 70um thick and black, red and high pigment coatings. And Irgacure 784's ultra-wide UV and visible light absorption bands make full use of the light source, so it has high sensitivity and photo-initiating activity. Irgacure 784 photo-disintegrated fragments are complexed with acrylates and have no surface migration, so they are safe and environmentally friendly. Irgacure 784 also has good thermal stability.

Irgacure 250 | CAS 344562-80-7

Irgacure 250 is a versatile cationic UV photoinitiator used to initiate epoxy or propylene oxide based photocuring systems. It can effectively cure cationic coatings and inks, such as printing inks, white paints, adhesives and so on. Particularly suitable for curing thick film systems and deep color systems. This product is a propylene carbonate solution with 75% active ingredient content.

Speedcure DETX (Photoinitiator DETX) | CAS 82799-44-8 | C17H16OS

Speedcure DETX is a highly efficient photocuring initiator that absorbs UV light and initiates chemical reactions. It is suitable for use in photocurable materials composed of unsaturated polyesters and acrylic monomers. Its greatest advantage is its good mutual solubility with organic solvents. It can be used in colorless or colored coatings. It can also be used in printing inks, wood furniture, decorative paints and adhesives. It is also used in combination with anionic initiators. effect.

Speedcure ITX (2-Isopropylthioxanthone) | CAS 5495-84-1 | C16H14OS

Speedcure ITX is a highly efficient photoinitiator for transparent or colored UV-cured screen printing inks, copy varnishes, lithographic inks, flexo inks, electronics, wood coatings, adhesives, and photoresists. The EDB is used at the same time, and the recommended addition amount is 0.2-2% w/w.

Speedcure EDB (Ethyl 4-dimethylaminobenzoate) | CAS 10287-53-3 | C11H15NO2

Speedcure EDB is a photosensitizer and does not have a photosensitizing effect by itself, but can be shared by a radical type photoinitiator to increase photosensitivity. Also known as a synergist.

live:5b3614ff27c1677c Skype
8613386404752 WhatsApp